Deutsch
EnglishCategories
Shipping country
Products description
Epoxyresin 40 Minutes New Size 280 g
(Epoxy 200 g + 80 g Hardener)
(Epoxy 200 g + 80 g Hardener)
Finally a high quality resin, in sufficient quantity and setting time! Quality, made in Germany. If you have ever had a bad experience with cheap resins and do not want to repeat this mistake, with this resin your needs are covered. Nothing is worse than a glue joint that comes undone again!
The 40-minute epoxy is a 2K epoxy resin adhesive. Resin and hardener are filled in bottles with 100 g resin each, as well as 40 g hardener
content, resulting in a total quantity of 280 g epoxy.
The adhesive is transparent, solvent-free and its working time is 90 minutes. It can be used to make flat, larger bondings or even hulls. It is suitable for universal assembly and repair of a wide range of materials such as metal, plastic, ceramics, glass, porcelain, stone, wood, concrete and rubber.
Adhesive joints become tensile and slack resistant as well as resistant to aging and media. There is a lasting resistance to water, gasoline and oil. The temperature resistance is up to approx. +120 °C.
Scope of delivery :
200 g resin + 80 g hardener
Suitable materials Metal, stone, concrete, porcelain, wood, glass and many plastics.
Unsuitable materials Polyethylene, polypropylene, Teflon®,polystyrene, soft PVC
Load Low, High, Medium
Resistance Gasoline, alkali, oil, acid, water
The 40-minute epoxy is a 2K epoxy resin adhesive. Resin and hardener are filled in bottles with 100 g resin each, as well as 40 g hardener
content, resulting in a total quantity of 280 g epoxy.
The adhesive is transparent, solvent-free and its working time is 90 minutes. It can be used to make flat, larger bondings or even hulls. It is suitable for universal assembly and repair of a wide range of materials such as metal, plastic, ceramics, glass, porcelain, stone, wood, concrete and rubber.
Adhesive joints become tensile and slack resistant as well as resistant to aging and media. There is a lasting resistance to water, gasoline and oil. The temperature resistance is up to approx. +120 °C.
Scope of delivery :
200 g resin + 80 g hardener
Suitable materials Metal, stone, concrete, porcelain, wood, glass and many plastics.
Unsuitable materials Polyethylene, polypropylene, Teflon®,polystyrene, soft PVC
Load Low, High, Medium
Resistance Gasoline, alkali, oil, acid, water
Temperature range - 40°C to + 100°C (depending on material and construction - higher temperatures also possible. Please refer to the technical data sheet)
Chemical base Epoxy resin
Viscosity high viscosity, medium viscosity
Pot life approx. 40 min (at room temperature)
Bonding technique Wet bonding
Tip:
We also recommend our thixotropic agents, carbon fiber chips, carbon powder for thickening the resin.
For the improvement of glued areas/surfaces we further recommend glass fiber fabric tapes.
See also the "Other accessories" tab.
Viscosity high viscosity, medium viscosity
Pot life approx. 40 min (at room temperature)
Bonding technique Wet bonding
Tip:
We also recommend our thixotropic agents, carbon fiber chips, carbon powder for thickening the resin.
For the improvement of glued areas/surfaces we further recommend glass fiber fabric tapes.
See also the "Other accessories" tab.
EU responsible person according to EU Regulation 2023/988 on general product safety (GPSR):
R&G Faserverbundwerkstoffe GmbH
Im Meißel 7 - 13
Bonholzstr. 17
71111 Waldenbuch • Germany
E-Mail: info@r-g.de
Hazards identification - Epoxy Resin L
Hazard components for labelling
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)] bisoxiraneReaction mass of 2,2'-[methylenebis(4,1-phenyleneoxymethylene)]dioxirane and [2-({2-[4-(oxiran-2-ylmethoxy)benzyl]phenoxy}methyl)oxirane and [2,2'-[methylenebis(2,1-phenyleneoxymethylene)]dioxirane
Reaction products of hexane-1,6-diol with 2-(chloromethyl) oxirane (1:2)
Signal word: Warning
Pictograms:
Hazard statements
| H315 | Causes skin irritation. |
| H317 | May cause an allergic skin reaction. |
| H319 | Causes serious eye irritation. |
| H411 | Toxic to aquatic life with long lasting effects. |
Precautionary statements
| P261 | Avoid breathing dust/fume/gas/mist/vapours/spray. |
| P273 | Avoid release to the environment. |
| P280 | Wear protective gloves / protective clothing / eye protection / face protection. |
| P305 P351 P338 | IF IN EYES: Rinse continuously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. |
| P333 P313 | If skin irritation or a rash occurs: Get medical advice / attention. |
| P501 | Dispose of waste according to applicable legislation. |
Special labelling of certain mixtures
| EUH205 | Contains epoxy constituents. May produce an allergic reaction. |
Hazards identification - Hardener L
Hazard components for labelling
3-aminomethyl-3,5,5-trimethyl-cyclohexylamineBenzyl alcohol
Cyclohexanemethanamine, 5-amino-1,3,3-trimethyl-, reaction products with bisphenol A diglycidyl ether
Homopolymer
2-piperazin-1-ylethylamine
Reaction mass of (1-phenylethyl)phenols andbis-(1-phenylethyl)phenols Salicylic acid
3-aminopropyltriethoxysilane
Signal word: Danger
Hazard statements
| H302 | Harmful if swallowed. |
| H314 | Causes severe skin burns and eye damage. |
| H317 | May cause an allergic skin reaction. |
| H361 | Suspected of damaging fertility or the unborn child. |
| H373 | May cause damage to organs through prolonged or repeated exposure. |
Precautionary statements
| P303 P361 P353 | IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water or shower. |
| P305 P351 P338 | IF IN EYES: Rinse continuously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. |
| P311 | Call a POISON CENTER/doctor. |
| P362 P364 | Take off contaminated clothing and wash it before reuse. |
| P405 | Store locked up. |
| P501 | Dispose of waste according to applicable legislation. |
